Footswitch enhances safety and saves time to spend searching for the off switch to prevent liquid splash. Also, it allows convenient and hands-free operation of peristaltic pump drivers. The work modes and setup procedures can be found in the specification tab.
Key Features
- Convenient for hands-free operation of the peristaltic pump
- Compatible with peristaltic pump variable speed control
- Easy to carry with the footswitch
Typical Applications
- Precision liquid handling or delivery
- Mainly designed for Laboratory and light industry applications
| Model | Work Mode | Set-up Procedure |
| JK-1 | Gated Mode and Trigger Mode | Insert a DB9 plug into the external port on the rear of a peristaltic
pump |
| JK-2 | Trigger Mode | a) Insert DB9 plug into external port on the rear of FK-1C. b) Power on FK-1C Dispensing Controller, turn internal/external control switch to ‘external control’. c) Press footswitch once (Note: press one time is enough), FK-1C will run until the setting time run out. |
| JK-3 | Gated Mode | Insert DB15 plug into external port in the rear of the peristaltic pumps The initial state of the peristaltic pump stopped when power on it. Pump runs when press down the footswitch; and pump stops when release
the footswitch. |
| JK-4 | Gated Mode and Trigger Mode | Insert DB9 plug into the external port in the rear of syringe pumps. Power on syringe pump, syringe pump should restore the previous
parameters before power-down then footswitch can be used to control the pump. |
| JK-5 | Trigger Mode | Insert DB15 plug into external port in the rear of the pump. Power on syringe pump, syringe pump should restore the previous
parameters before power-down then footswitch can be
used to control the pump. |
| JK-6 | Trigger Mode | Connect the wire of footswitch to the corresponding ends in the external control port of pump. Power on syringe pump, syringe pump should restore the previous
parameters before power-down then footswitch can be used to control the pump. |
Note: Gated Mode: Pump runs when press the footswitch down, but stops when release it.
Trigger Mode: Pump runs when press the footswitch once and release, but stops when press it again and release.| Thumb | File information |
 |
FK-1C operation manual.pdf File Size 1.02MB |
Peristaltic Pump Footswitch
- Brand: Longer
- Product Code: JK
- Availability: In Stock
-
$65.00
Available Options
Related Products
Intelligent Peristaltic Pumps L600-1FS , Flow Rate 0.15 µL/min -3,000 mL/min, Automatic Identification of Pump Head and Tubing
This intelligent peristaltic pump L600-1FS features using RFID technology to automatically iden..
$2,413.75
Industrial Peristaltic Metering Pump N6-30L, High Flow Rate 30 Liters/min, Motor Speed 0.1-300 RPM
The industrial peristaltic pump N6-30L model features extremely high flow rate up to 30 Liters per m..
$5,710.00
Industrial Peristaltic Metering Pump ZG600x, High Flow Rate 12 Liters/min, Motor Speed 60-600 RPM
The industrial peristaltic pump ZG600x model features extremely high flow rate up to 12 Liters per m..
$3,116.80
Industrial Peristaltic Metering Pump J025, High Flow Rate 28.5 Liters/min, Motor Speed 37.5 -300 RPM
The industrial peristaltic pump ASP-J025 model features extremely high flow rate up to 28.5 Liters p..
$4,020.20
New Era Footswtich for Syringe & Peristaltic Pumps
This foot switch allows the operator to start and stop a syringe or peristaltic pump remotely by pre..
$32.00